
Futuristic Flyer
부품 목록 (70)

Plate Special 1 x 2 with 1 Stud with Groove and Inside Stud Holder (Jumper)
×8
Plate Special 1 x 2 5.9mm Centre Side Towball Socket
×6
Plate 2 x 2 Corner
×6
Plate Special 1 x 1 with Clip Vertical [Thick Open O Clip]
×6
Slope Curved 2 x 1 No Studs [1/2 Bow]
×4
Plate Special 1 x 2 with 5.9mm Centre Side Towball
×4
Plate 2 x 2 Corner
×4
Tile 1 x 4 with Groove
×4
Plate Special 1 x 2 Side Handle [Free Ends]
×4
Plate 1 x 1
×4
Flag 2 x 2 Trapezoid with Flat Area between Clips
×4
Cone 1 x 1 [Top Groove]
×4
Wave / Flame Rounded with Base Rim
×4
Slope 30° 1 x 2 x 2/3
×4
Wheel Holder 2 x 2 Thin with Clips, Plane Single
×3
Plate 2 x 4
×3
Plate 2 x 3
×3
Plate 1 x 2
×3
Wheel Centre Small with Stub Axles (Pulley Wheel)
×3
Plate 2 x 6
×3
Technic Axle Pin with Friction Ridges Lengthwise
×3
Wedge Plate 3 x 4 with Stud Notches [Reinforced Underside]
×3
Bar 2L with Towball
×2
Slope Curved 2 x 1 Inverted
×2
Tile 1 x 4 with Groove
×2
Slope Curved 2 x 1 with Stud Notch Right
×2
Slope Curved 2 x 1 with Stud Notch Left
×2
Plate 2 x 2
×2
Plate 1 x 1
×2
Plate 1 x 1
×2
Brick Special 1 x 4 with 4 Studs on One Side
×2
Slope Curved 2 x 2 with Lip, No Studs
×2
Tile 2 x 2 with Groove
×2
Tile 1 x 2 with Groove
×2
Tile 1 x 1 with Groove
×2
Plate Special 2 x 2 with Only 2 studs
×2
Technic Brick 1 x 2 [1 Pin Hole]
×2
Plate 2 x 6
×2
Hinge Brick 1 x 2 Base
×2
Plate Round 2 x 2 with Axle Hole Type 1 (+ Opening)
×2
Wedge Plate 4 x 2 Right
×2
Wedge Plate 4 x 2 Left
×2
Hinge Brick 2 x 2 Top Plate Thin
×2
Tail Shuttle
×2
Brick Special 1 x 1 with Stud on 1 Side
×2
Plate Special 2 x 2 x 2/3 with Two Studs On Side and Two Raised [Solid Anti-stud]
×2
Slope Curved 4 x 1 No Studs [Stud Holder with Symmetric Ridges]
×1
Technic Axle Pin 3L with Friction Ridges Lengthwise and 1L Axle
×1
Plate 1 x 1
×1
Plate 2 x 8
×1
Technic Brick 1 x 2 with Axle Hole Type 1 [+ Opening] and Bottom Pin
×1
Cone 2 x 2 x 2, Open Stud
×1
Wedge Plate 12 x 3 Left
×1
Wedge Plate 12 x 3 Right
×1
Wedge Plate 4 x 6
×1
Wedge Plate 4 x 6
×1
Plate Special 1 x 1 with Tooth
×1
Wedge Plate 8 x 3, 22° Right
×1
Wedge Plate 8 x 3, 22° Left
×1
Wedge Plate 2 x 4
×1
Wedge Plate 2 x 4
×1
Brick Special 1 x 2 with Studs on 2 Sides
×1
Cone 1 x 1 [Top Groove]
×1
Wheel 31 x 15 Technic, 7 Pin Holes
×1
Technic Axle 4 with Stop
×1
Plate 1 x 1
×1
Plate 1 x 1
×1
Plate 1 x 1
×1
Plate 1 x 1
×1
Tile 1 x 1 with Groove
×1