
Red Go-Kart
부품 목록 (54)

Slope Curved 4 x 1 No Studs [Stud Holder with Symmetric Ridges]
×6
Technic Brick 1 x 2 [1 Pin Hole]
×4
Technic Axle Pin without Friction Ridges Lengthwise
×4
Plate 2 x 6
×4
Wheel 18mm x 14mm with Axle Hole, Fake Bolts and Shallow Spokes
×4
Plate Special 1 x 2 with Handle on End [Closed Ends]
×4
Plate Round 1 x 1 with Solid Stud
×4
Slope 30° 1 x 2 x 2/3
×4
Tyre 24 x 14 Shallow Tread (Tread Small Hub), Band Around Center of Tread
×4
Plate 2 x 4
×3
Plate 2 x 2
×3
Plate 1 x 2
×3
Bracket 1 x 2 - 1 x 4 [Rounded Corners]
×2
Tile Special 1 x 2 Grille with Bottom Groove
×2
Plate 2 x 2 Corner
×2
Plate Special 1 x 2 Side Handle [Free Ends]
×2
Technic Pin with Friction Ridges Lengthwise and Center Slots
×2
Brick Special 1 x 4 with 4 Studs on One Side
×2
Tile 2 x 2 with Groove
×2
Tile 1 x 2 with Groove
×2
Plate Special 3 x 2 with Rounded End, Hole
×2
Technic Axle 2 Notched
×2
Technic Steering Arm with 2 Pins
×2
Technic Axle and Pin Connector Perpendicular 3L with Centre Pin Hole
×2
Plate 1 x 3
×2
Technic Brick 1 x 8 [7 Pin Holes]
×2
Plate 1 x 4
×2
Technic Bush
×2
Technic Brick 1 x 6 [5 Pin Holes]
×2
Technic Pin 1/2
×2
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×2
Cone 1 x 1 [Top Groove]
×2
Plate Special 1 x 2 with Clip Horizontal on End
×2
Plate Special 1 x 2 [Top Clip]
×2
Slope Curved 2 x 2 x 2/3
×1
Technic Gear 20 Tooth Double Bevel with Axle Hole Type 1 [+ Opening]
×1
Technic Axle Pin 3L with Friction Ridges Lengthwise and 2L Axle
×1
Technic Steering Wheel Small (3 Studs Diameter)
×1
Technic Gear Rack 1 x 4
×1
Hinge Brick 1 x 2 Base
×1
Hinge Brick 1 x 2 Top Plate Thin
×1
Brick Round 2 x 2 with Axle Hole
×1
Plate Special 1 x 2 [Side Handle Closed Ends]
×1
Plate Special 1 x 2 with Clips Horizontal [Open O Clips]
×1
Technic Axle 9
×1
Tile 2 x 4 with Groove
×1
Wedge Plate 3 x 4 with Stud Notches [Reinforced Underside]
×1
Slope Curved 4 x 1 Double with No Studs
×1
Bracket 1 x 2 - 1 x 2 Inverted
×1
Technic Pin with Friction Ridges Lengthwise and Center Slots
×1
Technic Bush
×1
Technic Pin 1/2
×1
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×1
Plate Round 1 x 1 with Solid Stud
×1