
Fire Temple
미니피규어 (7)

Lord Garmadon (The Golden Weapons)
fig-000213×1

Zane (The Golden Weapons)
fig-000417×1

Master Wu (The Golden Weapons)
fig-000426×1

Nya (The Golden Weapons)
fig-000528×1

Kruncha
fig-002724×1

Samukai
fig-002726×1

Kai DX (The Golden Weapons)
fig-002727×1
부품 목록 (253)

Plate Special 1 x 2 with 1 Stud without Groove (Jumper)
×1
Technic Brick 1 x 6 [5 Pin Holes]
×1
Support Round 2 x 2 x 2 Stand with Reach-Through Center Hole
×1
Tile Round 2 x 2 with Bottom Cross
×1
Hinge Cylinder 1 x 3 Locking with 1 Finger and Technic Friction Pin with Round Hole
×1
Wedge Sloped 4 x 2 Triple Left
×1
Wedge Sloped 4 x 2 Triple Right
×1
Dish 3 x 3 Inverted [Radar]
×1
Weapon Pike / Spear Round End
×1
Slope Inverted 45° 4 x 2 Double with 2 x 2 Recessed
×1
Slope Inverted 45° 6 x 1 Double with 1 x 4 Recessed
×1
Weapon Axe Head, Clip-on (Viking) [Thin Clip]
×1
Projectile, Large Figure Weapon, Zamor Sphere / Ball with Marbled Bright Light Orange Pattern
×1
Technic Axle 8 with Stop
×1
Technic Brick Modified 2 x 2 with Solid Ball and Axle Hole
×1
Wave / Lightning Angular, Double with Marbled Trans-Purple Pattern
×1
Chain 16L [21 Links]
×1
Plate Round 1 x 1 with Solid Stud
×1
Technic Pin Connector Round [Slotted]
×1
Bar 6L with Stop Ring
×1
Bar 6L with Stop Ring
×1
Weapon Lightsaber Hilt with Bottom Ring
×1
Weapon Spike Flexible 3.5L
×1
Technic Brick 1 x 1 with Pin Hole
×1
Rubber Belt Small [15mm ID] [Round Cross Section]
×1
Wave / Flame Rounded Large with Marbled Trans-Orange Pattern
×1
Tile 2 x 4 with Japanese 'Dragon God' Print
×1
Plate Special 1 x 2 with Bar Up [Horizontal Arm 5mm]
×1
Technic Axle and Pin Connector 2 x 5 with Two Ball Joint Sockets [Closed Sides] [Open Axle Holes]
×1
Chain 6L [5 Links]
×1
Hinge Plate 2 x 2 Locking with 1 Finger on Top
×1
Animal Body Part, Dog Bone [Long]
×1
Weapon Sword Katana with Dragon Guard (The Sword of Fire)
×1
Creature Body Part, Dragon Head Upper Jaw with Dark Red Sections, White Teeth and Red Stripes Print
×1
Creature Body Part, Dragon Head Lower Jaw with White Teeth and Orange Spines Print
×1
Plate Round 1 x 1 with Solid Stud
×7
Plate Round 1 x 1 with Solid Stud
×4
Technic Pin with Friction Ridges Lengthwise and Center Slots
×3
Technic Pin 1/2
×2
Animal Body Part, Barb / Claw / Tooth / Talon / Horn, Small
×2
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×2
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×2
Plate Round 1 x 1 with Solid Stud
×2
Technic Bush 1/2 Smooth with Axle Hole Semi-Reduced
×1
Bar 1L with Clip [Cut Edges and One Side Hole] [Gap in Clip]
×1
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×1
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×1
Plate Round 1 x 1 with Solid Stud
×1
Plate Round 1 x 1 with Solid Stud
×1
Plate Round 1 x 1 with Solid Stud
×1
Flame / Headwear Accessory Plume / Feather, Triple Point
×1
Weapon Throwing Star / Shuriken with Smooth Grips
×1
Arm Skeleton Bent with Clips at 90° [Vertical Grip]
×1