Mountain Shrine
미니피규어 (2)
Kai DX (The Golden Weapons)
fig-002727×1
Skeleton with Round Brick Head and Round Red Plate Base (Bowling Pin)
fig-002987×1
부품 목록 (86)
Weapon Axe Head, Clip-on (Viking) [Thick Clip]
×8
Plate Special 1 x 2 Side Handle [Free Ends]
×6
Slope 33° 3 x 1
×6
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×5
Flag 2 x 2 Square [Thin Clips]
×4
Tile Special 1 x 1 with Clip and Straight Tips
×4
Wedge Plate 4 x 4 Cut Corner
×4
Brick Round 1 x 1 Open Stud
×4
Slope 75° 2 x 1 x 3 with Hollow Stud
×4
Cylinder 1 x 5 1/2 with Handle (Friction Cylinder)
×4
Plant, Round 1 x 1 - 3 Bamboo Leaves
×3
Plate Round 1 x 1 with Solid Stud
×3
Bar 1L with Top Stud and Two Side Studs
×3
Flag 2 x 2 Square [Thin Clips]
×2
Tile 1 x 4 with Groove
×2
Bar 8L - Two Stop Rings / One Pin, Technic Figure Ski Pole [Flat End]
×2
Brick 2 x 4
×2
Brick 2 x 2
×2
Brick 1 x 2
×2
Brick Special 1 x 2 Palisade [aka Log]
×2
Animal, Scorpion
×2
Plate 1 x 2
×2
Brick Special 1 x 2 with Vertical Clip [Open O Clip]
×2
Slope 45° 2 x 2
×2
Hinge Cylinder 1 x 2 Locking with 2 Click Fingers and Axle Hole, 9 Teeth
×2
Tile 1 x 2 with Groove
×2
Technic Axle 2 Notched
×2
Plate 1 x 6
×2
Technic Pin without Friction Ridges Lengthwise
×2
Technic Brick 1 x 2 [1 Pin Hole]
×2
Technic Brick 1 x 4 [3 Pin Holes]
×2
Hinge Brick 1 x 4 [Upper]
×2
Hinge Brick 1 x 4 [Lower]
×2
Brick Round 2 x 2 with Axle Hole
×2
Hinge Plate 1 x 2 Locking with 1 Finger on Side, with Groove
×2
Wedge Curved 2 x 3 x 2/3 Two Studs, Wing End
×2
Rock Panel 2 x 4 x 6
×2
Technic Axle Connector Hub with 4 Bars at 90°
×2
Bar 1L with Clip [Cut Edges and One Side Hole] [Gap in Clip]
×2
Weapon Spiked Ball Half with 2 Axle Holes
×2
Brick Special 1 x 1 with Clip Vertical [Thick U Clip, Solid Stud]
×2
Wave / Flame Rounded with Base Rim
×2
Brick Arch 1 x 4 x 2
×2
Equipment Telescope / Torch / Spyglass, Support Round 1 x 1 x 1 2/3
×2
Animal Body Part, Barb / Claw / Tooth / Talon / Horn, Medium
×2
Tile Round 2 x 2 - Thin Lifting Ring
×1
Brick Special 1 x 2 with Pin
×1
Plate Round 2 x 2 with Rounded Bottom [Boat Stud]
×1
Plate Round 2 x 2 with Rounded Bottom [Boat Stud]
×1
Brick 2 x 2
×1
Plate 2 x 4
×1
Plate 2 x 2
×1
Plate 2 x 2
×1
Plate 4 x 4
×1
Brick Round 2 x 2 x 2 Robot Body, Axle Holder '+' Orientation
×1
Bar 4L (Lightsaber Blade / Wand)
×1
Wedge Plate 8 x 8 Cut Corner
×1
Tile 2 x 2 with Groove
×1
Tile 1 x 2 with Groove
×1
Slope Inverted 45° 2 x 2 [Ovoid Bottom Pin, Bar-sized Stud Holes]
×1
Technic Brick 1 x 2 [1 Pin Hole]
×1
Technic Axle Pin without Friction Ridges Lengthwise
×1
Plate Special 1 x 2 with 1 Stud without Groove (Jumper)
×1
Plate 2 x 6
×1
Brick Special 1 x 1 with Headlight
×1
Plate Special 1 x 1 with Clip Light, Bar Hole [Thick Ring]
×1
Tile Round 2 x 2 with Bottom Cross
×1
Trading Card, Ninjago Deck #1: 3 - Kai DX - North American Version
×1
Trading Card, Ninjago Deck #1: 32 - Total Recall - North American Version
×1
Trading Card, Ninjago Deck #1: 22 - Weapon Force - North American Version
×1
Trading Card, Ninjago Deck #1: 72 - Reckless - North American Version
×1
Trading Card, Ninjago Deck #1: 19 - Gold Rush - North American Version
×1
Treasure Chest Bottom with Rear Slots, with Groove
×1
Treasure Chest Lid [Thick Hinge]
×1
Panel 1 x 2 x 1 [Square Corners]
×1
Chain 16L [21 Links]
×1
Turntable 4 x 4 Square Base, Locking
×1
Brick Round 4 x 4 Centre Hole
×1
Turntable 6 x 6 Round Red Base with Pearl Gold Top with Gold Faces on Red Print (Ninjago Spinner)
×1
Weapon Sword Katana with Dragon Guard (The Sword of Fire)
×1Sticker Sheet for Set 2254-1
×1Technic Pin without Friction Ridges Lengthwise
×1Bar 1L with Clip [Cut Edges and One Side Hole] [Gap in Clip]
×1Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×1Plate Round 1 x 1 with Solid Stud
×1
Arm Skeleton
×1