
Robo Master
미니피규어 (1)
부품 목록 (115)

Brick Special 1 x 1 with Headlight
×18
Plate Round 1 x 1 with Solid Stud
×18
Brick Special 1 x 2 with Grille
×12
Brick Round 1 x 1 Open Stud
×12
Wheel Hard Plastic Small (22mm D. x 24mm)
×12
Plate Special 1 x 2 Side Handle [Free Ends]
×10
Tile Special 1 x 2 Grille with Bottom Groove
×9
Slope Inverted 75° 2 x 1 x 3
×8
Dish 2 x 2 Inverted [Radar]
×8
Slope 45° 2 x 2
×7
Brick 2 x 2 Corner
×6
Technic Slope Long 1 x 6 with 3 Pin Holes
×6
Brick Special 2 x 2 with 2 Pins and Axle Hole
×6
Brick 1 x 2
×6
Tile Special 1 x 2 Grille with Bottom Groove
×5
Panel 3 x 2 x 6
×5
Brick 1 x 6
×5
Plate Special 1 x 2 with Handles [Flat Ends / Low Attachment]
×5
Brick Round 2 x 2 with Axle Hole
×5
Plate 2 x 2 Corner
×4
Lever Small Base with Light Gray Lever
×4
Panel 3 x 5 Solar / Deltoid with Clip [Hexagonal]
×4
Plate 2 x 3
×4
Plate 2 x 8
×4
Brick 1 x 3
×4
Slope Inverted 45° 2 x 2 [Ovoid Bottom Pin, Bar-sized Stud Holes]
×4
Slope Inverted 45° 2 x 2 [Ovoid Bottom Pin, Bar-sized Stud Holes]
×4
Plate 1 x 4
×4
Brick Special 1 x 2 x 2/3 with Studs on Sides
×4
Plate Special 1 x 1 with Clip Horizontal [Thick U Clip]
×4
Plate Round 1 x 1 with Solid Stud
×4
Flexible Hose 8.5L with Tabbed Ends (Ends same color as Tube)
×4
Hinge Plate 1 x 4 Swivel Top / Base - Solid Clip [Complete Assembly]
×4
Wedge 3 x 4 [No Stud Notches]
×3
Hinge Bar 2.5L with 2 and 3 Fingers on Ends (Pantograph Shoe Holder)
×3
Brick 1 x 4
×3
Plate 2 x 4
×3
Tile 1 x 2 with Robo Gold, Yellow, Red Print
×3
Slope 33° 3 x 2 with RoboForce Gold 'ROBO' and Blue and Yellow Circuitry Print
×3
Antenna 1 x 4 with Rounded Top
×3
Hinge Plate 1 x 2 with 2 Fingers and Hollow Studs
×3
Plate Special 1 x 4 Offset with Bar Holes
×3
Brick 2 x 2 Corner
×2
Wedge Plate 4 x 9 without Stud Notches
×2
Tile 1 x 4 with Gold, Red and Blue Circuitry Print
×2
Panel 3 x 3 x 6 Corner Convex
×2
Antenna 8H Whip
×2
Brick 2 x 4
×2
Brick 2 x 4
×2
Brick 2 x 4
×2
Brick 2 x 3
×2
Brick 2 x 3
×2
Brick 2 x 2
×2
Brick 2 x 2
×2
Brick 2 x 8
×2
Plate 2 x 2
×2
Plate 2 x 2
×2
Plate 2 x 8
×2
Slope 45° 2 x 3
×2
Hinge Plate 2 x 5 with Large Hole [Complete Assembly]
×2
Plate Special 3 x 2 with Rounded End, Hole
×2
Slope 33° 3 x 2
×2
Slope 33° 3 x 2
×2
Hinge Plate 2 x 9 with Hole Close to Hinge [Complete Assembly]
×2
Plate 1 x 3
×2
Plate 1 x 4
×2
Plate Special 1 x 2 with 1 Stud without Groove (Jumper)
×2
Hinge Brick 1 x 2 Base
×2
Hinge Brick 1 x 2 Top Plate Thin
×2
Tile 1 x 8 with Groove
×2
Slope 75° 2 x 1 x 3 with Open Stud
×2
Brick Special 1 x 2 x 2/3 with Studs on Sides
×2
Slope Inverted 45° 4 x 2 Double with 2 x 2 Recessed
×2
Brick 1 x 12
×2
Sticker Sheet for Sets 2154-1, 5129-1, 5384-1, 6856-1, 6900-1, 6915-1, 6958-1, 6975-1, 6982-1, 6999-1
×1
Equipment Control Panel
×1
Wedge 3 x 4 [No Stud Notches]
×1
Wedge Plate 3 x 6 Cut Corners
×1
Tile 1 x 4 with Groove
×1
Tile Special 1 x 2 with Handle
×1
Plate 2 x 12
×1
Brick 1 x 8
×1
Plate 2 x 4
×1
Plate 2 x 3
×1
Plate 1 x 2
×1
Plate 1 x 2
×1
Plate 4 x 12
×1
Plate 4 x 6
×1
Plate 4 x 8
×1
Slope 45° 2 x 2 with RoboForce Gold and Red Display and Circuitry Print
×1
Tile 1 x 2 with Digital Clock Print - '12:01' or '10:21'
×1
Tile 1 x 2 with Telemetry Panel Print
×1
Tile 1 x 2 with Red and Yellow Control Panel Print (Original)
×1
Tile 1 x 2 with Simple Computer Keyboard Print
×1
Brick Arch 1 x 6 x 2 - Thick Top with Reinforced Underside
×1
Hinge Plate 2 x 9 with Hole Close to Hinge [Complete Assembly]
×1
Plate 2 x 6
×1
Plate 2 x 6
×1
Plate 2 x 10
×1
Wedge Plate 8 x 4 Wing Left
×1