
Burj Khalifa
부품 목록 (63)

Slope 30° 1 x 2 x 2/3
×54
Plate 1 x 2
×47
Brick Special 1 x 2 with 2 Studs on 1 Side
×29
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×24
Tile 2 x 2 with Groove
×20
Technic Brick 1 x 2 with Axle Hole Type 1 [+ Opening] and Bottom Pin
×13
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×11
Brick 1 x 2
×8
Hinge Plate 1 x 4 Swivel Top / Base - Solid Clip [Complete Assembly]
×8
Tile 1 x 4 with Groove
×7
Plate 2 x 3
×7
Plate 2 x 8
×7
Slope Curved 4 x 1 Double with No Studs
×6
Tile 1 x 2 with Groove
×5
Tile 1 x 2 with Groove
×4
Technic Axle Connector Hub with 3 Axles at 120°
×4
Tile 1 x 6 with Groove
×4
Slope Curved 4 x 1 Inverted
×3
Tile Round 2 x 2 with Bottom Stud Holder
×3
Brick 1 x 1
×3
Plate 2 x 4
×3
Plate 2 x 8
×3
Tile 1 x 2 with Groove
×3
Technic Brick 1 x 2 [1 Pin Hole]
×3
Slope Curved 3 x 1 No Studs
×3
Brick Special 1 x 2 with Studs on 2 Sides
×3
Brick Special 1 x 1 with Stud on 1 Side
×3
Bracket 1 x 2 - 1 x 2 Inverted
×3
Bracket 1 x 2 - 1 x 2
×3
Tile Special 2 x 2 Inverted
×2
Plate Special 1 x 2 with 1 Stud with Groove and Inside Stud Holder (Jumper)
×2
Tile 1 x 4 with Groove
×2
Plate 2 x 12
×2
Tile Special 2 x 2 with Top Pin
×2
Technic Pin with Friction Ridges Lengthwise and Center Slots
×2
Plate 2 x 2
×2
Tile 1 x 2 with Groove
×2
Tile 1 x 1 with Groove
×2
Technic Wedge Belt Wheel [aka Pulley]
×2
Technic Pin 1/2
×2
Plate Round 1 x 1 with Open Stud
×2
Tile 2 x 2 Corner
×1
Technic Pin Connector Hub with 1 Axle
×1
Plate 1 x 2
×1
Plate 1 x 1
×1
Plate 4 x 10
×1
Plate 6 x 10
×1
Brick Round 1 x 1 Open Stud
×1
Plate Special 1 x 2 with 1 Stud with Groove (Jumper)
×1
Antenna 1 x 4 with Flat Top
×1
Tile 1 x 8 with "Burj Khalifa" Print
×1
Brick Special 1 x 1 with Studs on 2 Sides
×1
Technic Axle 5.5 with Stop [Rounded Short End]
×1
Technic Pin Connector Round [Slotted]
×1
Hinge Plate 1 x 4 Swivel Top / Base - Solid Clip [Complete Assembly]
×1
Brick and Axle Separator v2.0
×1
Technic Pin with Friction Ridges Lengthwise and Center Slots
×1
Plate 1 x 1
×1
Tile 1 x 1 with Groove
×1
Technic Pin 1/2
×1
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×1
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×1
Plate Round 1 x 1 with Open Stud
×1