
Level Three - Kit 8, The Forbidden Bridge
부품 목록 (92)

Brick Round 1 x 1 Open Stud
×12
Plate Round 1 x 1 with Solid Stud
×10
Brick 2 x 2 Corner
×8
Plate 1 x 2
×8
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×8
Brick 1 x 3
×7
Brick Special 1 x 2 Palisade [aka Log]
×6
Brick 1 x 2
×5
Brick 1 x 1
×5
Slope Inverted 45° 2 x 1
×5
Brick 1 x 2
×4
Slope 45° 2 x 2
×4
Tile 1 x 2 with Groove
×4
Slope Inverted 45° 2 x 2 [Ovoid Bottom Pin, Bar-sized Stud Holes]
×4
Slope Inverted 45° 2 x 1
×4
Plate 1 x 6
×4
Plate 1 x 4
×4
Slope 33° 3 x 1
×4
Cone 1 x 1 [Top Groove]
×4
Plate Round 1 x 1 with Solid Stud
×4
Technic Brick 1 x 1 with Pin Hole
×4
Brick 1 x 2
×3
Brick 1 x 2
×3
Brick 1 x 3
×3
Technic Brick 1 x 8 [7 Pin Holes]
×3
Plate Round 1 x 1 with Solid Stud
×3
Plate Round 1 x 1 with Solid Stud
×3
Slope 30° 1 x 2 x 2/3
×3
Plate Special 2 x 2 with Groove and Center Stud (Jumper)
×3
Tile Special 1 x 1 with Clip with Rounded Tips
×2
Brick Arch 1 x 5 x 4 [Continuous Bow]
×2
Plant, Leaves 4 x 3
×2
Brick 1 x 2 x 5 with Blocked Open Studs and Bottom Stud Holder with Asymmetric Ridges
×2
Brick 1 x 1
×2
Plate 2 x 2
×2
Plate 1 x 1
×2
Plate 4 x 8
×2
Brick Round 1 x 1 Open Stud
×2
Tile 1 x 2 with Groove
×2
Plate Special 1 x 2 with Door Rail
×2
Technic Pin Long with Friction Ridges Lengthwise and Stop Bush [3 Lateral Holes, Big Pin Hole]
×2
Brick 1 x 3
×2
Plate 1 x 3
×2
Fence Lattice 1 x 4 x 1
×2
Technic Brick 1 x 4 [3 Pin Holes]
×2
Plate Special 1 x 2 with 1 Stud with Groove (Jumper)
×2
Slope Inverted 34° 3 x 1 with Internal Stopper
×2
Bracket 1 x 2 - 2 x 2
×2
Plate Special 1 x 8 with Door Rail
×2
Tap 1 x 1 without Hole in Spout
×2
Cone 1 x 1 [Top Groove]
×2
Brick Special 1 x 1 with Stud on 1 Side
×2
Brick 1 x 2 x 5 with Blocked Open Studs and Bottom Stud Holder with Asymmetric Ridges
×1
Plate Special 1 x 2 Side Handle [Free Ends]
×1
Technic Pin with Friction Ridges Lengthwise and Center Slots
×1
Animal, Bat
×1
Plate 4 x 4
×1
Plate 4 x 6
×1
Plate 6 x 8
×1
Bar 4L (Lightsaber Blade / Wand)
×1
Technic Bush 1/2 Smooth with Axle Hole Semi-Reduced
×1
Brick Arch 1 x 8 x 2
×1
Animal, Frog
×1
Slope Inverted 45° 2 x 2 [Ovoid Bottom Pin, Bar-sized Stud Holes]
×1
Slope Inverted 45° 2 x 1
×1
Cone 2 x 2 x 2, Open Stud
×1
Cone 4 x 4 x 2, Axle Hole [Plain]
×1
Technic Beam 1 x 9 Thick
×1
Minifig Neckwear Bracket [One Stud]
×1
Technic Pin 1/2
×1
Slope 75° 2 x 1 x 3 with Hollow Stud
×1
Brick Special 1 x 1 Studs on 4 Sides
×1
Dish 2 x 2 Inverted [Radar]
×1
Technic Axle 5.5 with Stop [Rounded Short End]
×1
Technic Axle Connector Smooth [with x Hole + Orientation]
×1
Cone 1 x 1 [Top Groove]
×1
Bar 7 x 3 with Double Clips (Ladder) [Straight Clips]
×1
Plate Round 4 x 4 with Pin Hole
×1
Turntable 4 x 4 Square Base, Locking
×1
Cylinder Half 2 x 4 x 5 with 1 x 2 cutout
×1
Plate Special 4 x 6 with Trap Door Hinge [Long Pins]
×1
Plate Special 6 x 8 Trap Door Frame Horizontal [Long Pin Holders]
×1
Propeller 3 Blades 5 Diameter, Pin Hole
×1
Weapon Sai
×1
Technic Pin with Friction Ridges Lengthwise and Center Slots
×1
Technic Bush 1/2 Smooth with Axle Hole Semi-Reduced
×1
Technic Pin 1/2
×1
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×1
Plate Round 1 x 1 with Solid Stud
×1
Plate Round 1 x 1 with Solid Stud
×1
Plate Round 1 x 1 with Solid Stud
×1
Plate Round 1 x 1 with Solid Stud
×1