
Level One - Kit 1, Space Designer
미니피규어 (1)
부품 목록 (77)

Slope Curved 3 x 1 No Studs
×8
Plate Round 1 x 1 with Solid Stud
×8
Tile 1 x 4 with Groove
×6
Plate 1 x 2
×6
Cone 1 x 1 [Top Groove]
×6
Hinge Plate 1 x 4 Swivel Top / Base - Solid Clip [Complete Assembly]
×6
Slope Curved 4 x 1 No Studs [Stud Holder with Symmetric Ridges]
×4
Plate 2 x 4
×4
Plate 2 x 2
×4
Plate 1 x 2
×4
Brick Special 1 x 4 with 4 Studs on One Side
×4
Brick Special 1 x 1 with Headlight
×4
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×4
Brick Arch 1 x 6 x 3 1/3 Curved Top
×4
Brick Curved 1 x 2 x 1 1/3 with Curved Top
×4
Slope 18° 2 x 1 x 2/3 with 4 Slots / Grate
×4
Plate Round 1 x 1 with Solid Stud
×4
Slope 30° 1 x 2 x 2/3
×4
Brick 1 x 4
×3
Plate 2 x 3
×3
Plate 1 x 2
×3
Slope Inverted 45° 4 x 2 Double with 2 x 2 Recessed
×3
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×3
Brick 2 x 2 Corner
×2
Tile Special 1 x 2 Grille with Bottom Groove
×2
Bracket 1 x 2 - 1 x 4 [Square Corners]
×2
Technic Pin with Friction Ridges Lengthwise and Center Slots
×2
Plate 1 x 2
×2
Brick Round 1 x 1 Open Stud
×2
Tile 1 x 1 with Groove
×2
Plate 1 x 8
×2
Plate 1 x 3
×2
Plate 1 x 3
×2
Plate 1 x 3
×2
Slope Inverted 45° 2 x 2 [Ovoid Bottom Pin, Bar-sized Stud Holes]
×2
Plate 1 x 6
×2
Plate 1 x 6
×2
Technic Brick 1 x 2 [1 Pin Hole]
×2
Plate 1 x 4
×2
Plate Special 1 x 2 with 1 Stud without Groove (Jumper)
×2
Plate 2 x 6
×2
Antenna 1 x 4 with Rounded Top
×2
Plate Round 2 x 2 with Axle Hole Type 1 (+ Opening)
×2
Wedge Curved Inverted 6 x 4
×2
Bracket 1 x 2 - 2 x 2
×2
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×2
Wheel 18 x 14 with Pin Hole, Fake Bolts and Shallow Spokes
×2
Plate Special 1 x 1 with Clip Vertical [Thick Open O Clip]
×2
Tile Special 1 x 2 Grille with Bottom Groove
×1
Brick 2 x 4
×1
Brick 2 x 2
×1
Brick 1 x 2
×1
Plate 1 x 2
×1
Tile 1 x 2 with Avionics Copper, Red & Silver Controls Print
×1
Plate Special 1 x 2 with 1 Stud without Groove (Jumper)
×1
Plate 6 x 6
×1
Wedge Curved 6 x 2 Right, Inner Ridges
×1
Wedge Curved 6 x 2 Left, Inner Ridges
×1
Wedge 4 x 2 Right
×1
Wedge 4 x 2 Left
×1
Minifig Neckwear Bracket [One Stud]
×1
Brick Special 1 x 1 Studs on 4 Sides
×1
Wedge Plate 12 x 3 Left
×1
Wedge Plate 12 x 3 Right
×1
Plate Special 1 x 2 [Side Handle Closed Ends]
×1
Brick Separator v1.0
×1
Plate Special 1 x 2 with Clips Horizontal [Open O Clips]
×1
Windscreen 8 x 4 x 2 with 4 Studs and Handle
×1
Storage / Sorting Tray, Master Builder Academy
×1
Technic Pin with Friction Ridges Lengthwise and Center Slots
×1
Headwear Accessory Glasses / Goggles
×1
Tile 1 x 1 with Groove
×1
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×1
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×1
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×1
Plate Round 1 x 1 with Solid Stud
×1
Plate Round 1 x 1 with Solid Stud
×1