
Crater Cruiser
미니피규어 (2)
부품 목록 (85)

Plate Round 1 x 1 with Solid Stud
×10
Plate Special 2 x 2 with 1 Pin Hole [Split Underside Ribs]
×6
Technic Pin without Friction Ridges Lengthwise
×6
Cone 1 x 1 [No Top Groove]
×6
Slope Inverted 33° 3 x 2, No Connections between Studs, Ovoid Bottom Pin
×5
Tile Special 1 x 2 Grille with Bottom Groove
×4
Antenna 8H Whip
×4
Plate 1 x 3
×4
Dish 2 x 2 Inverted [Radar]
×4
Plate Special 1 x 1 with Clip Horizontal [Thick U Clip]
×4
Brick 1 x 4
×3
Plate 2 x 4
×3
Tile Special 1 x 2 Grille with Bottom Groove
×2
Wedge Plate 3 x 6 Cut Corners
×2
Plate 2 x 2 Corner
×2
Hinge Bar with 3 Fingers and End Stud (Control Lever)
×2
Windscreen 10 x 4 x 2 1/3 Canopy
×2
Wheel Hard Plastic Large (54mm D. x 30mm)
×2
Wheel Hard Plastic Medium (35mm D. x 31mm)
×2
Brick 1 x 2
×2
Brick 1 x 2
×2
Plate 2 x 4
×2
Plate 2 x 3
×2
Plate 2 x 2
×2
Plate 2 x 2
×2
Plate 1 x 2
×2
Plate 1 x 2
×2
Slope 45° 2 x 2
×2
Slope 45° 2 x 1 with Bottom Pin
×2
Tile 2 x 2 with Blue Screen, Silver and Red Panel Print
×2
Tile 1 x 1 with Groove
×2
Plate 1 x 8
×2
Plate 1 x 3
×2
Slope Inverted 45° 2 x 1
×2
Plate Special 1 x 2 with 1 Stud without Groove (Jumper)
×2
Plate Special 1 x 2 with 1 Stud without Groove (Jumper)
×2
Antenna 1 x 4 with Rounded Top
×2
Dish 4 x 4 Inverted [Radar]
×2
Tile 1 x 8 with Groove
×2
Engine, Strakes, 2 x 2 Thin Top Plate
×2
Hinge Plate 1 x 2 with 3 Fingers [Hollow Studs]
×2
Hinge Plate 1 x 2 with 2 Fingers and Hollow Studs
×2
Slope 33° 3 x 1
×2
Slope 33° 3 x 1
×2
Slope Inverted 34° 3 x 1 without Internal Stopper
×2
Hinge Vehicle Roof Holder 1 x 4
×2
Hinge Tile 1 x 2 1/2 with 2 Fingers on Top
×2
Wedge Plate 3 x 4 without Stud Notches
×2
Brick 1 x 12
×2
Wheel Hard Plastic Small (22mm D. x 24mm)
×2
Plate Round 1 x 1 with Solid Stud
×2
Wedge Plate 3 x 6 Cut Corners
×1
Tile 1 x 4 with Groove
×1
Hinge Plate 1 x 2 with 3 Fingers On Side
×1
Brick 2 x 6
×1
Brick 2 x 4
×1
Brick 2 x 2
×1
Brick 1 x 4
×1
Plate 2 x 4
×1
Plate 2 x 2
×1
Plate 1 x 2
×1
Plate 2 x 8
×1
Plate 4 x 8
×1
Slope 45° 2 x 2
×1
Tile 2 x 2 with Groove
×1
Technic Brick 1 x 2 [1 Pin Hole]
×1
Plate 1 x 4
×1
Plate 2 x 6
×1
Plate 2 x 10
×1
Plate 2 x 10
×1
Hinge Brick 1 x 2 Base
×1
Hinge Brick 1 x 2 Top Plate Thin
×1
Brick Round 2 x 2 with Axle Hole
×1
Cone 4 x 4 x 2, Axle Hole [Plain]
×1
Dish 4 x 4 Inverted [Radar]
×1
Plate Round 2 x 2 with Axle Hole Type 1 (+ Opening)
×1
Dish 6 x 6 Inverted, Radar / Webbed [Anti-studs at 90°]
×1
Hinge Tile 1 x 2 1/2 with 2 Fingers on Top
×1
Brick Round 2 x 2 x 2 with Axle Hole and Fins
×1
Bracket 8 x 2 x 1 1/3
×1
Wedge Sloped Inverted 6 x 4 with 2 Stud Connections
×1
Wedge Plate 3 x 4 without Stud Notches
×1
Panel 1 x 2 x 1 [Square Corners]
×1
Wedge Plate 8 x 8 with 3 x 4 Cutout
×1
Brick 1 x 12
×1
