
Duke Caboom's Stunt Show
미니피규어 (2)
부품 목록 (53)

Slope 45° 2 x 1 with Bottom Pin
×8
Wheel 8 x 6 with Slot
×8
Tyre 15 x 6 Offset Tread Small with Band around Center
×8
Hinge Brick 1 x 4 Locking with 1 Finger Vertical End and 2 Fingers Vertical End, 9 Teeth
×6
Slope Curved 2 x 1 No Studs [1/2 Bow]
×4
Plate Special 2 x 2 with Wheel Holders
×4
Plate Special Round 2 x 2 with Center Stud (Jumper Plate)
×3
Plate Special 1 x 2 with Clip Horizontal on Side
×2
Slope Curved 2 x 2 x 2/3
×2
Brick Arch 1 x 6 x 2 - Thin Top without Reinforced Underside [New Version]
×2
Plate Special 1 x 2 with 1 Stud with Groove and Inside Stud Holder (Jumper)
×2
Brick Arch 1 x 3 x 2 Inverted [Inside Bow]
×2
Tile 1 x 4 with Groove
×2
Brick 1 x 6
×2
Brick 1 x 6
×2
Slope 45° 2 x 2
×2
Brick Round 2 x 2 with Axle Hole
×2
Brick Round 2 x 2 with Axle Hole
×2
Brick Round 2 x 2 with Axle Hole
×2
Plate Special 1 x 4 with 2 Studs with Groove [New Underside]
×2
Slope 25° 1 x 8 x 3
×2
Slope 25° 1 x 8 x 3
×2
Tyre 21 x 6 City Motorcycle
×2
Wheel Centre 15 x 6 City Motorcycle with Stub Axles
×2
Cone 1 x 1 [Top Groove]
×2
Hinge Plate 1 x 2 Locking with 2 Fingers on Side, 9 Teeth
×2
Wave / Flame Rounded with Base Rim
×2
Wave / Flame Rounded Large with Marbled Trans-Yellow Pattern
×2
Slope 30° 1 x 2 x 2/3
×2
Slope Curved 4 x 1 Double with No Studs
×2
Tile Round 2 x 2 with Red/White Maple Leaf print
×1
Plate Special 8 x 9 x 2/3 with 1 x 4 Recessed
×1
Plate Special 9 x 16 x 2/3 with 1 x 4 Recessed
×1
Plate Round Corners 2 x 6 Double
×1
Hair Combed Sideways with Short Sideburns [Plain]
×1
Brick 1 x 2
×1
Plate 2 x 4
×1
Plate 4 x 6
×1
Tile 2 x 2 with Groove
×1
Tile 2 x 2 with Groove
×1
Slope 33° 3 x 2
×1
Plate 2 x 6
×1
Plate 2 x 6
×1
Brick Curved 2 x 2 x 2/3 Two Studs and Curved Slope End
×1
Brick Curved 2 x 2 x 2/3 Two Studs and Curved Slope End
×1
Brick 1 x 4 x 3
×1
Vehicle Base, Motorcycle Chassis, Long Fairing Mounts
×1
Panel 1 x 6 x 5 with 'Caboom', Dare Devil on Motor print
×1
Fairing, Motorcycle, Vintage
×1
Slope 30° 1 x 2 x 2/3
×1
Slope 30° 1 x 2 x 2/3
×1
Tile 2 x 4 with Groove
×1
Plate Special 1 x 2 with Bar Up [Horizontal Arm 5mm]
×1
